Smitty's RV-9A - Experimental Aircraft from Van's Aircraft The RV-9A from Van's Aircraft  
Howdy Ya'll
Howdy! I building an RV-9A! I'm an aviation nut and am excited about building my RV-9A from Van's Aircraft. Have a look around!
Smitty on FaceBook
Smitty on Twitter
Smitty on YouTube
Do what yer' Momma said...
Go Play!
Navigation
Homepage
Log Search
RV How-to Videos
RV TOOLS & BOOKS!
Places to FLY your RV!
Aviation Videos!
RV Resources
Become a PILOT!
RV-7/9 Drawings
ID: Pswd: RV-6A RV6A RV6 RV-6A RV7A RV7 RV-9A RV-9 RV9 RV-8A RV-8 RV8 RV-10 RV10 aviation aircraft Van's Aircraft RV8 RV8A RV-8 RV-8A RV-6 RV6 RV-6A RV6A RV-9 RV-9A RV9 RV9A RV10 RV-10 aopa eaa aviation experimental homebuilt airplane aircraft plane oshkosh
RV Construction Log
Preparation
Empennage
- Horizontal Stabilizer (49:40)
- Vertical Stabilizer (21:15)
- Rudder (32:15)
- Right Elevator (35:45)
- Left Elevator (30:50)
Wings
- Inventory & Setup (9:30)
- Left Wing Prep (54:30)
- Left Fuel Tank (45:20)
- Left Wing Skins (46:10)
- Right Wing Prep (34:15)
- Right Fuel Tank (47:50)
- Right Wing Skins (40:15)
- Ailerons (54:30)
- Flaps (40:30)
- Rods and ends (18:45)
Fuselage
- Fuselage Parts List
- Inventory and Setup (7:15)
- FireWall (14:30)
- F-704 Bulkhead (13:25)
- F-705 Bulkhead (14:20)
- Other Bulkheads
   and Longerons
(17:30)

- Tailcone (29:30)
- Center Section (35:15)
- Forward Section (52:40)
- Forward Assembly (24:30)
- Skins/Baggage Area (46:30)
- Seats & Seat Floors (30:15)
- Flaps & Gear Mounts (18:15)
- Fuselage Plumbing (14:0)
- Tail Feathers (16:35)
- Front Deck/Firewall (58:50)
Finish Kit
- Electrical (57:30)
- Electrical Part 2 (24:0)
- Canopy (22:30)
- Landing Gear (18:35)
How I Did Stuff
Pop-Rivet Dimpler 101
My Wing Jig
My Wing Cradle
Wing Cradle Mod
Tilting Tank Jig
Delrin Aileron Stops
Nutplate Preparation
Fiberglass 101
Events and News
Aviation Events
Aviation Events Around Texas
Fun Places To Fly in Texas
Aviation News
RV Groups & Support
Rivet Bangers
Van's Air Force
RV Information
How to Land an RV
Van's Aircraft
RV Resources
RV Photo Album
Completed RV-9's
RV-7/9A Drawings
Nut & Bolt Torque Values
Misc Goodies
Fuselage Parts List
How to Land an RV
My Tools
Fix a Heavy Wing
Paint Possibilities
Wings Inventory & Setup - 2/21/2006
Home  Previous Entry  Next Entry  Back
 
Share on:
Started work on the wing jigStarted work on the wing jig
I went down Lowes (aircraft supply) and bought two eight foot 2x4s, two ten foot 2x4s, two twelve foot 2x4s, some steel angles and some nuts and bolts. I plan to use the plywood that came with kit for reinforcement. I cut the eight foot 2x4s in half to make the foot supports on each end. Then I cut the ten foot 2x4s in half to make the vertical posts. Then I screwed the halfs and the two twelve foot 2x4s together.
Here's a shot of the steel anglesHere's a shot of the steel angles
They are 1 1/2" wide.
Put the jig base togetherPut the jig base together
After cutting the 12 foot 2x4s to proper length for the jig, I used my pneumatic brad nail gun to put the base together. The center beam is "T" up with the two 4 foot end footings, dead center on each. I finished attaching the plywood up by putting in some 2 1/2" wood screws into the 2x4s.
Attached the vertical postsAttached the vertical posts
I flipped the base over and tacked the posts in place with my brad nailer. Then I nailed and screwed the plywood on to hold the vertical posts in position. You'll notice the odd shape of the plywood. I did that to provide more strength to the posts that support the wing directly over the center beam on wig jig base.
Cut the vertical post bracesCut the vertical post braces
I had some old 2x4s laying around and made these braces to hold the vertical posts stationary. Once again I used my brad nailer to position everything, checking the posts out with my level. Then I went back and put in 3 1/2" wood screws to hold everything permanently.
Attached the steel anglesAttached the steel angles
At the advise of another builder, I put these steel angles at "armpit" height. I used 3 1/2" bolts to attach everything to the 2x4s. Leveling was quite a booger, since things tend to move while tightening the bolts.
Added a wood block to the steel angleAdded a wood block to the steel angle
This was some more advise from another builder. He told me that the steel angle scratches up the spar and a little wood block would protect it. You'll also notice that I put in extra wood screws in the steel angle, just prevent it from traveling.
Just had to try it outJust had to try it out
Apparently I got calculations just right. I was worried about having enough or too much distance between the posts. Now I'm sure that other builders will start asking questions here. Like "why don't you build both wings at the same time?". Very simple, I aint' got no room to do both wings at the same time. Momma is very protective of "her side" of the garage. The other question is probably "why don't you have steel angles to attach the bottom spar?" I have heard that this new "pre-drilled" wing aligns itself quite well and the bottom spar can float freely and is forced to line up perfectly with the top spar. Time to get to work!
Now for a leap into the FUTURE!Now for a leap into the FUTURE!
UPDATE 4/19/2006 - Now that I am working with this jig, I've decided to post the dimensions that I lucked out with for the jig. This shot is of the back of the jig on the outboard left wing, showing the distance between the main posts. As you can see, it's right at 133", or more. You can also see that I had to push the aluminum angle attachment out a little away from the jig arm, because the wing skin sticks out past the rib.
Another FUTURE shotAnother FUTURE shot
This shot is on the front side of the outboard left wing. As you can see, the height of the top of the main spar is right at 50 inches. Or as described to me by another builder, "make it chest height".
Yet another FUTURE shotYet another FUTURE shot
This picture shows the inboard left wing main spar resting on the arm of the wing jig. As you can see, there is a lot of play room for the spar. Also I thought that I wouldn't have to clamp this main spar down, but when you start putting on the skins, the weight of the skins caused the spar to twist.
Home  Previous Entry  Next Entry  Back
HELP FOR THE HOMEBUILDER

A website designed for Van's Aircraft Homebuilders, helping them find the information they need to build the most dynamic aircraft in the world.
The "cover your butt" section
This website was built to document the construction of an RV-9A in compliance with the FAA requirements needed to certify the aircraft. Any experiences and/or comments are by no means to be considered as instructions on how to build an RV-9A or any other aircraft.
This is website is owned and published by OpenAirNet, Inc. © 2015. All rights reserved.
Cool Stuff
How Far is that Airport?